The Picote Brush Coating™ System is a simple, fast and practical coating system used for drain and sewer renovation. Coat unlined or lined pipes or connections from DN32 – DN200 / 1¼” – 8″ with the Picote Coating Pump and Mini Miller combination. Coat anything from a small area (such as a lined connection) to entire piping systems, for example blocks of flats with our easy to use Smart Mixer and dual-colour 100% solids epoxy resin cartridges for cast iron, PVC, concrete or clay pipes.
The Coating Pump delivers the resin to the inside of the pipe and as the Mini Miller shaft rotates this in turn rotates the brushes that spread the resin over the inner pipe wall. The coating operation is started at the end of the pipe farthest from the access point. Resin is then pumped into the pipe and brushed on to the wall. The coating is then checked by pushing the brushes back to starting point and checking with the camera.
This is repeated over the length of the pipe being lined until the brush assembly reaches the access point. Subsequent layers can be coated in two to four hour intervals, unless hot air is applied to speed up the process to less than one hour between layers. Various coats are recommended depending on the pipe diameter or intended application.
The mini Miller powers the Mini Coating Pump. Can also be used with the Micro Miller.
This machine is intended for the following uses:
Always follow the manufacturer’s instructions when installing and using the machine with accessories.
GENERAL DESCRIPTION
This machine has a hand-held locking operator control buttom or “LOC”. When the control button is puched the pump is engaged and will operate until depressed.
This machine is intended for the following uses:
Always follow the Picote Solutions instructions when installing and using the machine with accessories.
This machine is intended for the following uses:
Simplify and speed up drying time of newly applied coatings with the portable smart heater.
Available in 230v and 110v versions. A safe heating option with a maximum air temperature of 55˚C/131˚F, including an automatic thermal cut-out in both motor and heating element. Provides a powerful air output.
Available with a 5m/16ft specialty hose with high strength & temperature resistance.
VOLTAGE & POWER SUPPLY
Ensure that the supply voltage is correct. The voltage of the power source must match the value given on the name plate of the machine within tolerances of plus minus 10%. Machines with a 230V plate can be used in 220V mains, 110V machines in the 120V grid.
GUIDING THE AIR INTO THE PIPE
Use hose clamps to attach the hose to the Picote Heater and guide the air into the pipe. Secure the hose to the pipe with hose pipe, tape or nozzle piece.
The battery operated Smart Mixer is a simple way to mix the dual component 100% solids epoxy resin. Simply lock and load the cartridges and dispense into the coating pump cup for a mess-free, easy solution.
Battery operated 2 component dispenser
The smart Mixer is intended for the following uses:
Mixing Picote Duel Coat Epoxy and Mastic for the Picote Coating System.
The Smart Mixer is specifically calibrated for the Picote Products.
Use Picote Mini Miller and Coating Pump to apply the resin. Always follow the Picote Solutions instructions when using the machine with accessories.
To begin the application process the correct brushes have to be selected and added to the head of the Miller shaft. If the pipe being repaired contains bends it may be necessary to select a pair of brushes that are separated by a flexible link to ensure an even coating through the bends. An unique feature of the system is that it is possible to coat for example a 4″ /DN100 pipe through a 2″ / DN50 clean-out due to the flexibility of the shaft and brushes.
The resin delivery hose is then attached to the shaft just behind the brush assembly. The CCTV camera head is also taped to the assembly just behind the delivery hose to allow the operator to see the coating operation as it progresses. With all in place the Smart Mixer lock and load self-mixing cartridge system can be used to dispense the 100% Solids Epoxy resin which is then added to the delivery side of the Picote Coating Pump. The lining run is ready to commence.
A battery operated 2-component dispenser.
INTENDED USE:
This Smart Mixer 2.0 is intended for the following use:
5. DUAL COAT EPOXY
Thank You! We have received your request and will contact you shortly.
There was an error while trying to send your request. Please try again.